5000lph Pre-Treatment System RO Water System Pure Water Reverse Osmosis Treatment Machine

Product Description

5000lph Reverse Osmosis System Water Filter RO Water Desalination For Commercial Use

The reverse osmosis water treatment system can separate, extract, purify and concentrate the reverse osmosis method that is
greater than the osmotic pressure according to the different osmotic pressures of various materials. When the RO membrane is
located on one side of the selective membrane, by applying pressure to the solution, RO membranes remove many types of macromolecules and ions from solution. Solutes such as iron, viruses, bacteria and solids are retained on the pressurized side of
the membrane, while pure solvents are allowed to pass through the other side of the membrane

Model	JFRO-5000L
Producing Capacity	5m³/h	RO membrane	8″
Recovery Rate	75%	Power Supply	Tri-phase: 110/220/380/415V  50/60Hz
Operating Pressure	0.5-1.6MPa
Desalination Rate	99%	Power Consumption	15KW/14KW
Filtration Accuracy	0.0001 micron	Control Type	Manual control / Auto control
Feed Water Quality	SDI<5   Free Chlorine Concentration<0.1mg/L TDS<2000mg/L
Features	Removes impurities such as inorganic ions, bacteria, viruses, organic matter and colloids from raw water.

 
The working principle of reverse osmosis membrane
  1.A membrane that is selective for permeable substances is called a semi-permeable membrane, and a membrane that can only permeate a solvent but cannot permeate a solute is generally called an ideal semi-permeable membrane. When the same volume of dilute solution (such as fresh water) and concentrated solution (such as salt water) are placed on both sides of the semipermeable membrane, the solvent in the dilute solution will naturally pass through the semipermeable membrane and flow to the concentrated solution side spontaneously, This phenomenon is called penetration. When the osmosis reaches equilibrium, the liquid level on the side of the concentrated solution will be higher than the liquid level of the dilute solution by a certain height, that is, a pressure difference is formed, and this pressure difference is the osmotic pressure.
  2.The size of the osmotic pressure depends on the inherent properties of the solution, that is, it is related to the type, concentration and temperature of the solution and has nothing to do with the properties of the semipermeable membrane. If a pressure greater than the osmotic pressure is applied on the solution side, the flow direction of the solvent will be opposite to the original osmotic direction, and it will begin to flow from the concentrated solution to the dilute solution side. This process is called reverse osmosis.
  3.Reverse osmosis is a reverse migration movement of osmosis. It is a separation method that separates the solute and solvent in the solvent by means of the selective interception of the semi-permeable membrane under the pressure drive. It has been widely used in the purification of various solutions. The most common application example is in the water treatment process, using reverse osmosis technology to remove impurities such as inorganic ions, bacteria, viruses, organics and colloids in raw water to obtain high-quality pure water.
  4.The reverse osmosis membrane is a semi-permeable membrane artificially synthesized by a special process in order to realize the reverse osmosis phenomenon of the aqueous solution. The pore size of the reverse osmosis membrane is 0.0001µm, and only the solvent in the aqueous solution, water, can pass through, while its solute cannot pass through the reverse osmosis membrane. The diameter of the virus is 0.02-0.4µm, and the diameter of the bacteria is 0.4-1.0µm. Therefore, the water passing through the reverse osmosis membrane is truly pure water.

Does the reverse osmosis pure water system frequently start and stop, has a great impact on the equipment?
   If the reverse osmosis pure water system is designed for continuous operation, in actual operation, there will be start and stop at different frequencies. When the membrane system is out of operation, low-pressure flushing with its produced water or pretreated water should be used to replace the concentrated water with high concentration but containing scale inhibitor in the membrane element. It should also be considered not to introduce air due to system leakage, because if Parts lose water and dry out, and irreversible permeate flux loss may occur. If the machine is down for 24 hours, no action is necessary. However, if the downtime exceeds the above provisions, the protective solution storage system or the membrane system should be flushed regularly to reduce the impact on the equipment caused by the start-up of the equipment.

Does the reverse osmosis pure water system frequently start and stop, has a great impact on the equipment?
   If the reverse osmosis pure water system is designed for continuous operation, in actual operation, there will be start and stop at different frequencies. When the membrane system is out of operation, low-pressure flushing with its produced water or pretreated water should be used to replace the concentrated water with high concentration but containing scale inhibitor in the membrane element. It should also be considered not to introduce air due to system leakage, because if Parts lose water and dry out, and irreversible permeate flux loss may occur. If the machine is down for 24 hours, no action is necessary. However, if the downtime exceeds the above provisions, the protective solution storage system or the membrane system should be flushed regularly to reduce the impact on the equipment caused by the start-up of the equipment.
 

Q: What's the type of your company? Manufacturer or Trading agent?

A: We're the Hi-tech manufacturer in Water treatment industrialfor almost two decades, we specialized in integrating Research & Development, Manufacturing, Sales, Engineering installation andConsulting on water treatment and water purification equipment and technologies.

 

Q: What kind of information need to be provided for product selection?

A: What 's the raw source of your water? If possible, please provide Water Analysis Report.

B: What's your request on the output capacity of the equipment?

C: What's the application for the project?

D: What's the piping standard applied in your local market?

E: Do you need on-site installation guidance?

 

Q:How can I choose the products which can be perfectly match my case?

A: Tailor-made solutions will be provided by Jufu's professional engineer based on your requirements. All the pain-points
of the project will be highlighted and solved for overall optimization.

 

Q: What's your payment terms?

A: Deposit in advance and balance before delivery.

 

Q: What's the leadtime?

A: It depends. 3-5 weeks for general products.

 

Q:What's your warranty?

A: Jufu offers 1 year warranty for the products. The product itself can work for 5 years with proper use and maintenance.